Lenovo Legion Y27Q-20 review

While LG’s 27GL850-B is still hard to get, it’s display panel is available for other brands to use in their design. Currently the Lenovo Legion Y27Q-20 and Viewsonic’s XG270QG are available for purchase. Let’s look at their key features.

27GL850-BY27Q-20XG270QG
Adaptive SyncFreesync/G-Sync compatible Freesync/G-Sync compatible G-Sync
Refresh144Hz165Hz165Hz
USB ports2 (back)3 (2 side, 1 bottom)3 (bottom)
StandHeight, tilt, pivot
Metal and plastic
Height, tilt, pivot, swivel
Fully metal
Height, tilt, pivot, swivel
Other Audio out
VESA100
Audio out/mic in
VESA100
Headphone hook
Low blue light mode
Audio out
VESA100
Headphone hook,
Low blue light mode
Mouse cable hook
RGB features
Hood
MSRP$499.99$549.99$675.99

It will be interesting to see if the G-Sync module in Viewsonic’s offering will make a difference to overdrive behaviour at lower framerates. Note that there is also a Y27GQ-20 ($629.99 MSRP) available which has a G-Sync module if that’s your requirement. This display does only come with an 8bit TN panel though.

Unboxing and features

Unboxing the monitor is a nice experience, the monitor is packed in styrofoam and has a box with a handle and a lid that’s able to close again which makes transporting the monitor easier. In the box you’ll find:

  • Displayport 1.4 cable
  • HDMI 2.0 cable
  • USB 3.1 type B upstream cable
  • Power brick
  • Power lead
  • Documentation

The base of the stand and it’s upright will have to be assembled with an integrated screw, after this it’s possible to attach the panel to it’s base with some locking hooks. No tools are required. The base feels very heavy and strong, it’s all metal. The bottom plate is a thick piece of metal with holes in it and a blue underside which looks quite pleasing and unique.

The display itself is technically the same as in LG’s 27GL850. It features a 1440p resolution, 165Hz refresh rate at 10bits and internally processes this at 8bit+frc. It’s contrast ratio is stated at 1000:1 but given the performance of LG’s offering it’s expected to be around 850:1.

Mounting the display to a VESA100 arm went well but the cables attach to the monitor quite low at the back of the display. The connections are oriented vertically so when mounted to an arm, you will notice the USB upstream and DisplayPort cables exiting from the bottom. Getting some right-angle adapter should fix this if you’re after a clean setup.

First impressions and build quality

Turning on the monitor for the first time greets you with a Lenovo logo and a vibrant image due to it’s wide color gamut support. The interface is controlled by using the front buttons, there are six in total of which one is reserved for a power toggle. They feel nice and clicky. When the menu is closed, the five buttons will act as shortcuts to the following settings.

  • Game settings (profiles, overdrive and on screen framerate)
  • Input toggle
  • On screen refresh rate options
  • Birghtness and color settings
  • Main osd menu

All pages can be accessed from all shortcuts by backing out of the current page. It would’ve been nice if the buttons could’ve been assigned custom functions. I personally do not enjoy the menu system all that much but after setting up the monitor you’re not likely to use it all that much. I only wish there would’ve been a way to quickly toggle sRGB mode. I do enjoy that the menu gives you an option to set a timeout so that it stays open for longer when adjusting settings.

There is one usb port on the underside and two on the left side of the monitor. There is also a 3.5mm audio jack on the left which can be used as a headphone TRS output as well as a TRRS headset connection providing a 24 bits at 48KHz microphone input. This input also seems to provide some form of echo cancelation. The input provides some decent quality.

Issues

An issue with the OSD I noticed is that it won’t show if your refresh rate is set to anything below 100Hz. I also prefer to have most of the USB ports on the back of the display. Having two on the back gives the option to plug in a keyboard and mouse which leaves one on the left free for charging a phone. Lenovo has chosen to have two on the left side and one on the back, not a huge deal at all but noteworthy.

Another minor issue is that the monitor, on NVIDIA at least, defaults to 8bits per channel even though it can do 10bits at 165Hz. Going into the NVIDIA control panel and setting the color settings to manual allows you to enable 10bpc. You’ll be hard pressed to see the difference though unless you like staring at gradients.

Picture quality

Out of the box

The monitor comes preset with Game mode set to Off, these modes are different profiles and all have their own character. Besides Off there are: FPS1/2, Racing, RTS and Game 1/2. All modes basically lock out every other setting in the monitor so leaving Game mode to Off will give most flexibility. The monitor offers controls for Brightness, DCR(dynamic contrast), Saturation, Contrast, Color Temp. and Dark Boost. It does however lack a mode to change gamma, so unless Lenovo decides to add this to a future firmware update you’ll be stuck with the default gamma. Let’s hope it’s set right then!

sRGB mode

Let’s first take a look at sRGB mode which should be factory calibrated, this mode locks out all settings except brightness.

Whitepoint6423K
Contrast863:1
Average dE0.88
Maximum dE1.54

These results are pretty great, the monitor has no problems display sRGB content in this mode. The only slight problems here are a slight green tint in greyscales and slightly elevated gamma values near pure white. This means that highlights might get clipped slightly as seen in the last picture above which was taken with a camera.
It’s below average contrast ratio for an IPS display is expected with this panel and even though it’s a bummer, it’s very difficult to see the difference between this panel and an IPS panel that has a 1000:1 contrast ratio or higher.

Unclamped gamut

Comparing the uncalibrated display against DCI P3 and sRGB yields worse results. Setting the whitepoint required me to set the Color Temp. to RGB 100/97/100 since the default values gave a green hue, setting the display to it’s Normal white point setting also resulted in a better whitepoint.

Color performance compared to DCI P3 is actually pretty good but gamma performance falls short here.

Comparing the uncalibrated display to sRGB also shows a pretty poor result but this is to be expected when comparing an unclamped gamut to sRGB. The gamma respons is still pretty poor though. Let’s see how calibration can improve results then.

Post calibration

The monitor has been calibrated with an X-Rite i1Display Pro colorimeter using DisplayCAL software. DisplayCAL is using the “LG 27GL850 by 4KM for newDP (i1 Pro)” correction with an sRGB gamma target. Note that this is only the gamma response (luminance) and not clamping the color gamut.

Calibrating the display is pretty straightforward since there is not a lot you can and should adjust. sRGB mode is set to off, contrast is set to 85 and reducing brightness to around 20 will give around a 120cd/m2 brightness level. Measuring and profiling then gave the following results.

Contrast840:1
sRGB gamut99.8%
Adobe RGB gamut 85.9%
DCI P3 gamut 94.8%
Min brightness 62cd/m2
Max brightness 380cd/m2

The green tint in the greyscale response has been corrected. Comparing the color gamut to sRGB shows that it’s easily capable of covering the entire gamut. Looking at DCI P3 shows that it can cover most of it’s gamut but that it lacks some saturation towards green and cyan. Adobe RGB is also covered pretty well here with slight under saturation in the reds and greens which results in slightly under-saturated yellows.

Compared against other color spaces

Measuring this profile against several color spaces gives the folowing results. Note that Adobe RGB has several high dE spikes since the monitor is technically not able to display the full saturation targets of Adobe RGB.

sRGB DCI P3 D65 2.2 Adobe RGB
Average dE0.340.591.16
Maximum dE1.121.45.35

Below are parts of the measurement report for sRGB, DCI-P3 and Adobe RGB verifications showing more detail.

These results are excellent and anyone who has access to a calibration device should have a great experience with this monitor while doing color-critical work.

Color profiles

Several people asked me if I would be willing to share my color profile so here they are. I should warn you that every display will have it’s own characteristics so my color profiles will probably not be 100% accurate for your display. I would recommend you to use DisplayCal to import and manage these profiles, this way you’re sure that the profile will always be applied. Simply install DisplayCal, ignore ArgyllCMS installation and go to file, load settings and import the zip files. Then click on install profile next to the drop down menu and set as system default. You can find my two profiles here. One is for sRGB emulation mode and the other is for wide gamut mode.

Display uniformity

My unit has a very uniform image with only the left side showing slight vignetting when looking at a uniform color.

Backlight bleed

Bleed can show if a panel isn’t mounted in it’s chassis well since pressure points on the panel will show through as dark spots or highlights. Lenovo has done an great job on my unit as hardly any glow is visible. When looking at a black screen at a 2s shutter speed (compared to 1/4th on the uniformity black image above, so overexposed by 3 stops), slight clouding can be seen with most of it visible at the bottom left and top right. In person though, I can only see the bottom left bleed on a black background. This result is better than both 27GL83A’s I’ve tested before.

Backlight bleed (overexposed by three stops)

Off-angle glow

IPS display all suffer from glow when you look at them from an angle. Below are two images where the first one shows a worst-case scenario (45 degrees up and to the side). This image shows a dark red/brown glow which is comparable to the 27GL83A I reviewed earlier. Looking at the display from a 45 degree angle to the side shows very little glow.

Motion handling

This monitor supports up to 165Hz, interestingly LG didn’t include this setting in their own product. The monitor also support Freesync and G-Sync compatibility. Connecting it to my Nvidia GTX1080Ti enabled G-Sync automatically but there is one issue currently.

G-Sync issues

The monitor suffers from moments of having a black screen when framerates vary a lot. It looks like the display has issues when switching between LFC mode to regular mode and from regular to 165+ Hz. First time I noticed this I was in a game of CS:GO and while opening the buy menu, the screen went black. This to about three seconds and then it returned. For more investigation I ran Battlefield 5 at 200% resolution sclale and max details which resulted in a 30-50fps range. While playing I noticed several moments where the monitor when black and even mentioning “Cable not inserted”. When the display then went into standby it got connected again and everything resumed as normal until the next time. I’m not sure whether Lenovo is responsible or NVIDIA has a driver issue currently. My unit is running firmware LG1.1.
To my understanding, most/all of the people with this issue are running a 10-series NVIDIA gpu so AMD and 16/20-series owners might have no issues.
Turning off G-Sync also fixes the problem but will of course introduce tearing.

Motion clarity

So does 165Hz on this display have any benefit compared to 144Hz? I do not have the equipment to measure response times but this website does and they have measured the average response time to be 5ms, down from 6.02ms on the 27GL850. For a 165Hz mode to have any benefit, pixel response times have to be 6.06ms or below so being able to push the average response time down should help here.
The display has three modes of overdrive Off, Normal and Extreme. Interestingly, the extreme mode doesn’t look too bad when running at 165fps but this quickly changes when the framerate lowers as much inverse ghosting appears.
In order to compare how different modes compare I’ve takes several photo’s. They were taken at 1/60th for 144Hz and 165Hz and 1/30th for 60Hz. Several pictures were taken while panning the camera in sync with the ufo’s and the best ones were picked for comparison.

165Hz

First let’s take a look at 165Hz, the image remains sharp and as you can see setting overdrive to Extreme adds some additional clarity but also introduces some inverse ghosting. This is pretty minimal though so playing a game 165fps or more is definitely possible with this setting set to extreme although artifacts will be visible.

144Hz

Switching over to 144Hz, the image remains very sharp in motion but having overdrive set to Extreme introduces a lot more inverse ghosting to the point where I would consider this unusable.

60Hz

Dropping all the way down to 60Hz will of course introduce quite a lot of blur. These picture were taken at 1/30th of a second instead of 1/60th as to keep the shutter speed roughly half of the refresh rate. With overdrive set to Normal the image remains quite stable and no overshoot is visible. Setting overdrive to Extreme is completely unusable at this refresh rate though.

Response times compared to 27GL83A-B

When looking at a side-by-side comparison between it’s noticable that Lenovo’s further tweaks to overdrive has indeed resulted in a slightly clearer image in motion. The black lines on the ufo have slightly more contrast which is also true for the complete image. This is also noticable when comparing both in person even though both displays are already excellent in this regard.

Conclusion

Lenovo’s LEGION Y27Q-20 is a very capable monitor, I feel they have improved over the 27GL850 and 27GL83A by improving motion handling as well as a nicer stand. Color performance is excellent in both wide-gamut (after calibration) and sRGB applications. The current issues with NVIDIA’s G-Sync compatibility are a concern though and I hope Lenovo or NVIDIA will be able to provide a fix in the near future. It would also be great if the monitor would come with some form of gamma controls since stock settings are not ideal.

Pros Cons
• 165Hz is a nice bonus over LG.
• Slight improvement in motion clarity because of this and better tuning.
• Great all-metal stand.
• sRGB mode is very accurate.
• Excellent performance after calibration.
• Integrated 3-port-USB hub.
• 3.5mm headphone jack with mic input
• G-Sync issues on 10-series NVIDIA.
• $50 more expensive than 27GL850.
• Out of box gamma results not great.
• OSD not showing under 100Hz.
• Cable management difficult due to low connection points.

I do this stuff for my own enjoyment but if you are feeling generous you can buy me a cup of coffee.

33 thoughts on “Lenovo Legion Y27Q-20 review

  1. Thank you for this review. It’s fantastic. I bought the monitor on the back of your review and I love it. My panel does have some backlight bleed in the bottom corners that is visible in dark scenes but I’m most likely just going to live with it. It’s otherwise fantastic.

    Like

  2. Simply install DisplayCal, ignore ArgyllCMS installation and > go to file, load settings and import the zip files. <

    this part is not clear because it wont let me to select that folder or load the 7z.

    PS. sRGB is not very good color but better at white and black so use the user as color temp then use RGB as 100/100/100 or 100/97/100 which looks much better.

    Like

  3. Hey! does this monitor have an external power block or just a normal direct power cable. I hate external power blocks for monitors. Also how are the connections oriented? downwards or straight out? And are the OSD buttons actual buttons or are they touch?

    Like

    1. Hello there, sorry for my delayed reply. It uses an external power brick, all connections are oriented downwards except for the side usb ports and audio jack. OSD buttons are clicky switches, no touch.

      Like

  4. Very nice review. Got the monitor myself today coming from a VA panel. Red seems to pop a bit too much and i toned in down via windows color calibration, and toned down the saturation option to 48 in the OSD. Is this the best way? Or should i activate sRGB? overall picture looks a bit dull when i do that.

    Like

  5. You should also do input lag tests. This is so close to being on par with the bigger monitor review sites. Great work though!

    Like

    1. You can turn on HDR in Windows’ display settings, it’s under HD color. DCI-P3 is not a setting, it simply displays DCI-P3 in it’s unclamped gamut. Having a DCI-P3 calibrated color profile will help with accuracy.

      Like

  6. Thanks for the very detailed review. One question though: I have a R9 390 but I’m only able to set the monitor to 120hz (via Windows Advanced Display Settings). However whatever I’ve tried I can’t get it to anything higher. Funny enough Windows shows the recommended resolution as 3840 x 2160. I’m using the DP cable that came with the monitor.

    Thanks in advance for any help!

    Like

    1. Maybe as additional information: I can get it to 144hz with AMD custom soultion. But if I do that, I can only use 8 bit colour depth. My feeling is, that the R9 390 isn’t able to run the monitor with 1440p, 144+hz and 10bit, because it’s too old.

      Like

  7. Hi, thanks a lot for this review. Would you mind sharing your calibrated settings? Contrast, brightness, RGB values and etc. I dont have the tool kit.

    Like

  8. So with your colour profiles, do you still keep sRGB enabled from the monitor settings after you apply the profile or was the profile meant to substitute for the sRGB mode in that we can just keep it on default settings (sRGB off)

    Like

  9. Were you ever able to resolve the G-Sync issues with the 10x series cards? I heard rumors on reddit about a firmware being released if you reach out to support. Thanks!

    Like

  10. I still get black screens at 165 Hz using a GTX 1080 and this fix. I also can’t select 10 bpc when the refresh rate is over 120 Hz. Once in a while the monitor randomly switches to 10 bpc at e.g. 144 Hz. This causes a periodic black screen and colorful lines start constantly appearing.

    Sometimes the 165 Hz option just disappears completely from Nvidia Control Panel. Overall, seems like a pretty “buggy” monitor full of issues to me…

    Like

    1. You’re the first I’ve heard talking about so many issues. Maybe there is something wrong with your unit or you’re using a faulty cable. Make sure you use displayport when available.

      Like

  11. For the exact same price

    4990SEK

    RX 5700XT.

    Would you choose the

    LG 27GL83A-B
    or
    Lenovo Legion Y27Q-20

    If you could only have one and had to return the other one.

    Thanks in advance!

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

Create your website at WordPress.com
Get started
%d bloggers like this: